How to make stair stringers
How do you make a stair stringer from scratch?
Can you use 2×10 for stair stringers?
What Is a Stair Stringer? Think of a stair stringer as the framing for a set of stairs. They are cut to create the shape of the stairs. As such, they determine the height of each step as well as the depth of each tread.
What size lumber is used for stair stringers?
2x12s
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
How far apart do stair stringers have to be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
Can I use 2×12 for stair treads?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. … The stair treads should be at least 36 inches wide.
How do you cut a 2×12 stringer?
How long of a 2×12 do I need for stairs?
10.5″
We suggest 10.5″ for 2×12 or 2 – 2×6 Treads. Treads may be cut to suit other widths. Either B or C is required.
How deep should a deck step be?
The maximum height of a single step is 7.75 inches, and all stair heights must be within 3/8 inch of each other, to keep the stairs regular. The depth (also called tread or run) of each step should be a minimum of 10 or 11 inches depending on the type of stairs.
What is building code for stairs?
The IRC stairs code states that, to comply with stairway requirements, the minimum width for residential stairs be no less than 36 inches. The stair riser code is up to 7.75 inches, and can not vary more than 3/8 of an inch. There are also section codes in place for standard stair tread dimensions.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
Are stairs 45 degrees?
No matter what the measurements are, the angle between them (treads and risers) will be maintained at 90 degrees. … For example, if you were crazy and built a staircase with a 12 inch tread and riser, then the angle of the stringer to the floor would be 45 degrees. A more common angle is about 37 degrees.
How do you build deck stairs with pre made stringers?
Are risers required on deck stairs?
Most high-end deck projects use closed risers to finish the stairs. … They also are often in violation of IRC code for decks over 30″, which maintains that they meet the same requirements as guardrail infill. Stair risers may not have openings present that would allow a 4” diameter sphere to pass through.
What is the most comfortable angle for stairs?
Stair codes and guidelines prefer an angle of around 37° for normal stairways (the green area in our illustration) and around 7° for ramps (the yellow area in our illustration). Steeper slopes or angles are permitted for stepladders in certain applications as you can see in the illustration.
What angle should a step be?
30 to 50 degrees
Standard stair angle by application
Standard stairs have an angle of 30 to 50 degrees while steep stairs like alternating tread stairs and ship stairs have an angle between 50 and 70 degrees. Ladders have an angle range between 60 and 90 degrees.
What is normal step height?
Riser Heights
In the United States, the step height standard should be between 7 or 7 ¾ inches at the most, and no less than 4 inches. You should follow other measurements if given by local building codes. In Canada, the maximum step riser height is 8 ¼ inches.
What should the rise and run be for stairs?
The OSHA standard for rise and run of stairs is maximum 9.5″ rise and minimum 9.5″ run (tread depth).
What is the correct rise for stairs?
Over the years, carpenters have determined that tread width times riser height should equal somewhere between 72 to 75 inches. On a main stair, the maximum rise should be no more than 8 1/4 inches and the minimum run should be no less than 9 inches.
What is the standard for stair treads and risers?
Stair riser heights shall be 7 inches (178 mm) maximum and 4 inches (102 mm) minimum. Stair tread depths shall be 11 inches (279 mm) minimum. The riser height shall be measured vertically between the leading edges of adjacent treads.
How many steps before a landing is required?
– A landing is required every 12′ of vertical stairway rise. – The landing should be at least as wide as the stairway that it serves.
What is a comfortable step height?
Rule one says that rise plus run (r+R) should equal 18 inches. Why? That’s what most people find to be a comfortable stride on most stairs. You can cheat a bit up or down, but below 17” and more than 19” will result in steps that require strides either too big or too small for most people.